内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

A comprehensive survey on the methods of angle of attack measurement and estimation in UAVs

Angle of Attack (AOA) is a crucial parameter which directly affects the aerodynamic forces of an aircraft. The measurement of AOA is required to ensure a safe flight within its designed flight envelop. This paper intends to summarise a comprehensive survey on the measurement techniques and estimation methods for AOA, specifically in Unmanned Aerial Vehicle (UAV) applications. In the case of UAVs, weight constraint plays a major role as far as sensor suites are concerned. This results in selecting a suitable estimation method to extract AOA using the available data from the autopilot. The most feasible and widely employed AOA measurement technique is by using the Multi-Hole Probes (MHPs). The MHP measures the AOA regarding the pressure variations between the ports. Due to the importance of MHP in AOA measurement, the calibration methods for the MHP are also included in this paper. This paper discusses the AOA measurement using virtual AOA sensors, their importance and the operation.     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

基于DOA聚类算法的ARM抗有源诱偏技术研究

有源诱偏技术是雷达对抗反辐射导弹的一种重要手段,可以大大降低反辐射导弹的作战效能。为提高对敌目标的精确打击能力,在分析闪烁诱饵诱偏原理的基础上,针对有源诱偏干扰下被动雷达测角精度与稳定度不高的问题,通过对有源诱偏信号的时域特征进行分析,提出一种基于脉冲前沿检测的DOA聚类分选算法,找出前沿超前的辐射源信号,实现了高性能抗有源诱偏干扰和高精度抗干扰测向。仿真结果表明,该技术可以有效对抗四点源有源诱偏干扰。     

航天嵌入式软件数组越界缺陷特征研究

根据统计,数组越界是航天嵌入式软件开发过程中出现最多且最容易被遗漏的缺陷类型之一.目前自动化检测数组越界多基于抽象解释、符号执行、程序模型检验等方法,这些方法在误报、漏报、可扩展性等方面的表现依赖于软件及缺陷特征.分析了近三年航天嵌入式软件第三方测试中发现的94个数组越界问题,从缺陷模式和缺陷表现形式两方面分析得出10项航天嵌入式软件数组越界缺陷特征,并提出对设计具体检测方法关键的若干启示.进一步基于这些特征和启示探讨了数组越界检测算法针对中断驱动型程序的改进方向.     

一种基于OPTICS聚类的仅测角导航目标检测算法

仅测角自主导航方法具有设备简单、复杂度低，功耗低的优点，在空间任务中具有广泛的应用前景.针对中远距离下空间目标特征少的特点，提出了一种利用基于OPTICS聚类算法的空间目标检测方法，可用于仅测角导航过程中的目标检测.对原始星图进行预处理提取星点及目标点，并结合星图识别的结果选择部分帧，使用经过改进的OPTICS聚类方法获得目标运动轨迹.最后，使用本文中的算法对软件仿真出的含有目标的高精度星图进行处理验证了算法的可行性.在卫星相对于空间目标抵近过程中，目标检测的水平误差及垂直误差小于0.15°的帧数分别占到了85.4%以及99.6%.相比AVANTI实验中的目标检测方法，减少了在轨任务中相关参数的调节，进一步提升了算法的自主性.     

先进战斗机过失速机动大气数据融合估计方法

可控的过失速机动是先进战斗机超机动性能的重要标志，飞机飞行包线的扩大已超出传统的大气数据系统测量范围，可靠的迎角、侧滑角、总压、静压等飞行大气数据是制约先进战斗机过失速机动中飞行控制的关键因素。以中国推力矢量验证机为对象，基于过失速机动飞行试验的数据，开展大气参数估计与验证研究。结合过失速机动的时间与空间特性，研究了基于风速、地速、空速矢量和惯性姿态、导航参数的大气参数融合计算方法；针对过失速大迎角状态下飞机周围气流非定常、模型非线性导致的融合大气参数误差的复杂特性，进一步构建深度神经网络，对机动状态融合迎角、侧滑角的强非线性误差进行拟合。仿真和飞行试验表明：该方法可在大迎角飞行状态下实现主要大气参数的融合估计，过失速机动过程中融合迎角误差优于2.3°，融合得到的大气参数可为过失速大迎角机动飞行控制提供可靠的大气参数状态反馈。     

机载托架自动校准系统的设计与实现

为了解决机载托架传统校准方法精度低、耗时、费力等问题,设计了一种高精度、高效率并且操作简单的成品托架自动校准系统。该系统运用调平精度较高的"循环多次"最高点不动调平方法,建立高精度机载托架校准的静力学数学模型,运用VC与Matlab的COM接口编程技术开发机载托架自动校准系统,并建立良好的人机交互界面。试验结果表明,利用该方法对机载托架进行校准,无论是校准精度还是校准效率都较传统方法有很大提高。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。